Waterworks .25 Handshower On Hook with Metal Handle Uživatelský manuál stáhnout pdf

Installation Guidelines

W A T E R W O R K S

Waterworks is a registered trademark of Waterworks Inc.

04.11.07

.25 Handshower On Hook

PTHS25

These guidelines have been prepared for the professional contractor to aid in the installation of:

.25 HANDSHOWER ON HOOK (PTHS25) All dimensions are based on origin specification and are

subject to change and variation. Please consult your Design Associate for current specifications.

"Ø

IMPORTANT

To ensure this product is installed properly, you must

read and follow these guidelines.

The owner/user of this product must keep this

information for future reference.

The risk of scalding exists until the installer has

properly calibrated the temperature setting on the

thermostatic valve (sold separately).

Observe all local plumbing and building codes.

Product uses dual check valves for backflow

prevention. Local plumbing codes may require a

vacuum breaker to be installed in-line to handshowers.

Please consult with local plumbing codes.

A wall valve (sold separately) controls on/off/volume

and must be installed for proper operation of this

product.

This product must be installed by a professional

contractor.

Inspect this product to assure you have all parts

required for proper installation.

Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface

ROUGH IN:

1. Install a wall valve (sold separately) at the desired

location.

2. Determine the ideal location of the inlet/hook

assembly based on the clients preference.

3. Finish the rough in by installing a well supported

female ips elbow.

4. Sweat a piece of

" copper pipe of appropriate length

onto a

" male x

" sweat adapter. Thread the

copper and adapter assembly into the female elbow in

the wall. The copper must protrude 1" from the

surface of the finished wall

ELBOW/HOOK INSTALLATION:

1. Unpack the hook/elbow (5) and verify the adapter (1)

is threaded completely into the hook/elbow.

2. To verify alignment of the hook/elbow and adapter,

make a mark at 12:00 that extends from the

hook/elbow onto the adapter.

3. Unthread the adapter from the hook/elbow then slide

the adapter onto the copper. The face of the adapter

should NOT extend more than 1

" off the face of

the finished wall.

4. After verifying fit, make sure the mark made in step 2

remains at 12:00 then sweat the adapter onto the

copper. If it is not aligned, the hook/elbow will not

thread on completely and cause a leak or not align

properly so the elbow/hook points down at 6:00.

5. Allow the adapter to cool then slide the escutcheon

onto the adapter.

6. Thread the hook/adapter onto the adapter making

sure the washer (4) is in place

7. Install the hand shower hose and verify proper

function. A flow restrictor is located in the base of

the hand shower.

If further assistance is required, please contact Product

Support at 1-800-927-2120 (8am-7pm EST).

1 2

Installation Guidelines 1

Shrnutí obsahu

Strany 1 - Installation Guidelines

Installation GuidelinesW A T E R W O R K SWaterworks is a registered trademark of Waterworks Inc.04.11.07.25 Handshower On HookPTHS25 These g

Strany 2

Installation GuidelinesW A T E R W O R K SWaterworks is a registered trademark of Waterworks Inc..25 Handshower On HookThese guidelines have

Komentáře k této Příručce

Žádné komentáře

Waterworks .25 Handshower On Hook with Metal Handle Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Příslušenství pro vodu Waterworks .25 Handshower On Hook with Metal Handle. Waterworks .25 Handshower On Hook with Metal Handle User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Příslušenství pro vodu Waterworks .25 Handshower On Hook with Metal Handle