Waterworks Universal Three Way Thermostatic Diverter Valve Tr Uživatelský manuál stáhnout pdf

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST

UNIVERSAL

Diverter Plates for Pressure Balance and Thermostatic Shower Systems

INSTALLATION GUIDELINES

Page 1 of 1

7.19.2013

These guidelines have been prepared for the professional contractor to aid in the installation of:

UNIVERSAL DIVERTER PLATES FOR PRESSURE BALANCE & THERMOSTATIC SHOWER SYSTEMS

(STYLE #'S UNDV2P, UNDV2T, UNDV3P & UNDV3T).

All dimensions are based on original specification and are subject to change and variation.

Please consult your Design Associate for current specifications.

Two Way Pressure Balance

Style No. UNDV2P

Two Way Thermostatic

Style No. UNDV2T

Required Valve

Style # GUDV23

(SOLD SEPARATELY)

Required Valve

Style # GUDV14

(SOLD SEPARATELY)

Three Way Pressure Balance

Style No. UNDV3P

Three Way Thermostatic

Style No. UNDV3T

Required Valve

Style # GUDV65

(SOLD SEPARATELY)

Required Valve

Style # GUDV66

(SOLD SEPARATELY)

IMPORTANT:

¾ To ensure this product is installed properly, you

must read and follow these guidelines.

¾ The owner/user of this product must keep this

information for future reference.

¾ This product must be installed with a Two or Three

Way Diverter Valve (SOLD SEPARATELY) & Handle

Trim (SOLD SEPARATELY). Please refer to the

specific valve & specified handle trim installation

guidelines for rough-in requirements.

¾ This product is supplied with a Plastic Insert that

may be removed if the Handle Trim Adapter does

not fit through it.

¾ Be sure your installation conforms to federal state,

and local codes. In the State of Massachusetts, all

installations must comply with the rules and

regulations set forth within 248 CMR.

¾ This product must be installed by a professional

licensed contractor and must be onsite prior to

rough-in, this allows the installer to visualize the

installation.

¾ Inspect this product to ensure you have all the parts

required for proper installation.

¾ Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

¾ DO NOT use putty on fittings.

TRIM PLATE INSTALLATION:

¾ See Figure - 01 for Steps 1-3.

¾ Diverter valve must be roughed-in & finished wall

must be complete prior to trim plate installation.

1. Follow the installation guidelines for the specific

handle trim used for proper cuts to be made to

threaded tube and stem of cartridge.

2. After the proper cuts have been made, slide diverter

plate over the modified diverter valve components.

3. Hold plate against the wall, making sure the foam

gasket is behind it. Thread & tighten handle trim

onto the threaded tube, making sure the handle is

aligned. Note: Discard the plastic insert if the handle

trim does not fit through it.

Figure - 01

HANDLE TRIM ASSEMBLY

[SOLD SEPARATELY]

FINISHED WALL

DIVERTER PLATE

PLASTIC INSERT

FOAM GASKET

DIVERTER VALVE

THREADED TUBE

& CARTRIDGE STEM

[SOLD SEPARATELY]

¾ If further assistance is required, please contact

Product Support at 1-800-927-2120 (8am-6pm EST).

INSTALLATION GUIDELINES 1

Shrnutí obsahu

Strany 1 - INSTALLATION GUIDELINES

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST UNIVERSAL Diverter Plates for Pressure Balance and Thermostatic Shower Systems INSTALLATION GUIDELINES

Komentáře k této Příručce

Žádné komentáře

Waterworks Universal Three Way Thermostatic Diverter Valve Tr Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Příslušenství pro vodu Waterworks Universal Three Way Thermostatic Diverter Valve Tr. Waterworks Universal Three Way Thermostatic Diverter Valve Trim User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Příslušenství pro vodu Waterworks Universal Three Way Thermostatic Diverter Valve Tr